Designed in an innovative modular fashion, Falco controller allows you to upgrade your system anytime from 1 to 10000 doors by connecting to server via TCP/IP Local Area Network configuration and manage by Falco Premium System software. This modular, cost-efficient upgrade strategy ensures that you can always keep pace with your emerging security requirements while meeting your ongoing budgetary objectives. Its wide capabilities make it suitable for even the largest, most complex building architectures and the most demanding security requirements. The FALCO IP door controller has 4 wiegand reader ports, and has a space for either the entry or exit reader to be mounted. The controller can be configured to work with almost all reader technologies without hardware change - including with Wiegand, ABA track 2 and contact-less Read/ Write smart card. This IP controller provides direct communication through TCP/IP network. Each controller will consist of it's own IP address. Communication speed as compare to RS-485 is faster (100 Mbit/s). Feature Advanced Design The Falco door controller uses the latest state-of-the-art flash memory technology which allows firmware upgrade. Essential equipment settings, card database and transaction database are stored in EEPROM, so that there is no loss of data during power outage. Multiple Entry Access Mode There are 3 different entry access modes that you can set to adjust to your security requirements: Card only, PIN only and Card & PIN only. This means a door can be programmed to operate on different entry access mode at either same or different time for each day of the week, including weekends and holidays. For example, a door can be programmed to operate on 'Card only' entry mode during office hours but automatically switch to 'Card & PIN only' entry mode after office hours. Use of Single Card to Perform Multiple Functions The prowess of the Falco door controller is its ability to allow a single card to perform multiple functions through software control. The types of functions consist of normal access control, programming, Arm/Disarm, guard tour, etc. Schedules Settings Up to 50 sets of weekly timers, where each daily timer consists of 3 sets of start and stop time interval settings can be used for system behavior control. These timers are also tagged to a day-of-week selection, which are used for all timers' related operations, such as locking and unlocking of doors, activating of User PIN function, etc. Quite often you may want to unlock the office main entrance door during office hours, but the door shall be locked during lunch break and after office hours. This requirement can be achieved through timer(s) controls. Alarm Monitoring Function Alarm monitoring functions become available when Falco controller is operated from Falco PC software. Each Falco controller is equipped with 8 supervised inputs and 4 relay output. Since the maximum system size for Falco controller is 100 doors, such a system will have 800 input points and 400 output points for alarm monitoring usage. Users can set complex combination from Falco PC software. There after, arming or disarming of alarm zones, and switching on or off output groups can be performed from any reader PIN keypad connected to the Falco controller. Power Supply Falco Controller comes with battery charging and a power regulation circuit. The input power requirement is 14VAC, and a lead-acid battery can be connected to the charger output. In addition, AC power failure, low battery cut off and battery low status sensing are built-in. 10-Digit MIFARE Falco Controller now able to reads 10-digit card number instead of 6-digit. The more digit it can read, lower the possibility of reading duplicate card number. This will reduce the chances of number repeats or duplicates in large card volume. Identities mismatch might happen when there are duplicates card number and this will cause error to attendance report. Specification • MCU : Motorola/ Freescale 16-bit CPU Running at 25Mhz • Memory : 64KB FlashROM, 8KB RAM, 32KB EEPROM • Watchdog : 1 Internal • Operating Temperature: 0C to 60C • Humidity Range: 0-95% non-condensing • Protocol Support: TCP, IP, UDP, DHCP, ICMP, and ARP • Network Interface : TCP/IP, LAN, WAN • Communication Interface : Onboard Ethernet Port (TCP/IP)10/100BaseT • Relay Output : 10A (1 Form C- can configured to NC or NO) • Power Supply : 14VAC input, 13.8V output, 1.5 ~ 3.0A output • Current Consumption : 200-300mA (without the EM Lock)/1.5A max • Dimensions : 50mm(H) x 152mm(W) x 127mm(D) • Configurable : 1-door or 2-door (with expansion board) and alarm monitoring • Supervised Input :2 Supervised input (Onboard) • Digital Input : 3 Input • Output : 2 Relay Output (Onboard), 3 Open-Collector Power Output (100mA-Onboard) • Large Memory : Stores up to 100,000 user cards and 50,000 transactions • Power Fault Detection: Loss of AC Power and battery voltage low • PIN only, Card only, and Card Plus PIN Operation Modes • Lock-out of a card when its PIN is wrongly entered repeatedly • Stored Event :2,000 upgradeable to 50,000